Materials
· Body
The whole unit is manufactured in recycled aluminium with painted finish.
Body, lid and latch in aluminium injection finished with grey powder paint (RAL 9007). Internal dissipator in aluminium extrusion black anodized finish and diffuser in toughened glass.
· Arm
The luminaire arm is presented in two sizes (75 and 150 cm) with the aim of adapting the distance between the light source and the column in accordance with the type of road to be lit up and the presence of trees overhead. On being aluminium extrusion, the arm can be adapted to any length between both measurements, or extend to 3 m, the latter incorporating a reinforcing brace. The arm incorporates an aluminium injection clamp at one of its ends.
· Columns
Columns with a height of 8.20 or 10.20, with two sections of circular cross-section tube, the lower part Ø 168 mm and the upper part Ø 127 mm.
The columns are manufactured in hot galvanized steel and painted finish for 1 or 2 luminaires at the same or a different height. The 8.20 and 10.20 m columns are also manufactured in extruded aluminium.
Luminaire
· Optical unit
Set of PC LEV 1700 optical lenses.
· Electronic equipment
Offers the possibility of powering the lamp from 350 mA to 500 mA.
Adjustable 1-10V or Dali power sources can be supplied as an option.
· Fastening to column
Fastening of the body with aluminium half-clamp using stainless steel screws.
Lamp
The Candela LED incorporates a LED module which allows the following options:
· 140W - 96 LED (500 mA -12064 lm - 3950k )
· 105W - 72 LED (500 mA – 9048 lm – 3950 k)
· 70W - 48 LED (500 mA – 6032 lm – 3950 k)
Luminaire efficiency >90%
Upper flux fraction 0,0%
· Power suply 230 V - 50 Hz
· Degree of protection IP 66
· Electrical Class I
· EC Marking
Maintenance
This luminaire does not require maintenance.
Instalation
The element is delivered dismantled in four parts:the column, the luminaire, the arm with the front clamp and, finally, the rear clamp with the screws.
The column is fixed by means of a concrete bucket installed in situ and anchor bolts, 20/30 cm below the level of the finished paving. The foundations must foresee the groove for the electric connection. The template and the anchor bolts are delivered with the column.
Weights
· Luminaire 14,5 Kg.
· Stainless steel columns 140 Kg (8,20 m), 170,5 Kg (10,20 m) y 204 Kg (12,20 m)
Materials
· Body
The whole unit is manufactured in recycled aluminium with painted finish.
Body, lid and latch in aluminium injection finished with grey powder paint (RAL 9007). Internal dissipator in aluminium extrusion black anodized finish and diffuser in toughened glass.
· Arm
The luminaire arm is presented in two sizes (75 and 150 cm) with the aim of adapting the distance between the light source and the column in accordance with the type of road to be lit up and the presence of trees overhead. On being aluminium extrusion, the arm can be adapted to any length between both measurements, or extend to 3 m, the latter incorporating a reinforcing brace. The arm incorporates an aluminium injection clamp at one of its ends.
· Columns
Columns with a height of 8.20 or 10.20, with two sections of circular cross-section tube, the lower part Ø 168 mm and the upper part Ø 127 mm.
The columns are manufactured in hot galvanized steel and painted finish for 1 or 2 luminaires at the same or a different height. The 8.20 and 10.20 m columns are also manufactured in extruded aluminium.
Luminaire
· Optical unit
Set of PC LEV 1700 optical lenses.
· Electronic equipment
Offers the possibility of powering the lamp from 350 mA to 500 mA.
Adjustable 1-10V or Dali power sources can be supplied as an option.
· Fastening to column
Fastening of the body with aluminium half-clamp using stainless steel screws.
Lamp
The Candela LED incorporates a LED module which allows the following options:
· 140W - 96 LED (500 mA -12064 lm - 3950k )
· 105W - 72 LED (500 mA – 9048 lm – 3950 k)
· 70W - 48 LED (500 mA – 6032 lm – 3950 k)
Luminaire efficiency >90%
Upper flux fraction 0,0%
· Power suply 230 V - 50 Hz
· Degree of protection IP 66
· Electrical Class I
· EC Marking
Maintenance
This luminaire does not require maintenance.
Instalation
The element is delivered dismantled in four parts:the column, the luminaire, the arm with the front clamp and, finally, the rear clamp with the screws.
The column is fixed by means of a concrete bucket installed in situ and anchor bolts, 20/30 cm below the level of the finished paving. The foundations must foresee the groove for the electric connection. The template and the anchor bolts are delivered with the column.
Weights
· Luminaire 14,5 Kg.
· Stainless steel columns 140 Kg (8,20 m), 170,5 Kg (10,20 m) y 204 Kg (12,20 m)
